|
|
Post by AJR on Aug 3, 2021 17:57:33 GMT -7
Hi Jeff, please put me down for 1 in each class plus 1 in each shark pool. Thanks, Mike Thanks Mike! You are on the List. |
|
|
|
Post by AJR on Aug 3, 2021 17:58:14 GMT -7
Jeff, Put me in for two cars in the SS TJet class. Thanks! Thanks Wally! You are on the List. |
|
|
|
Post by chriskingsley65 on Aug 5, 2021 20:20:38 GMT -7
Hey jeff put in for two in each. Please and thank you!
|
|
|
|
Post by AJR on Aug 8, 2021 14:25:53 GMT -7
Hey jeff put in for two in each. Please and thank you! Thanks Chris! You are on the List. |
|
|
|
Post by pete on Aug 18, 2021 13:03:42 GMT -7
How many 2.4 motors have you guy's blown up getting ready for this next race? I'm in for 2 @ $40.00.
I'll be sending my 6.0 arm cars, I don't want to try to find one that will hold up. The comm plates came off both arms.
|
|
|
|
Post by skillet on Aug 18, 2021 13:51:02 GMT -7
I can't find tyco timmed 2.4ohm ,only for viper. So I haven't blown any up lol.
|
|
|
|
Post by wbj on Aug 18, 2021 14:54:56 GMT -7
Lucky Bob has 2.7 ohm Wizzard arms with Tyco timing. Not sure if this helps or not?
|
|
|
|
Post by pete on Aug 18, 2021 16:03:00 GMT -7
WBJ those are a green arm. I know they are fast but very unreliable at 18 volts. It should be fun to watch at 26.
With the two I picked up for this race, I think that when the arm was epoxied (or not) it wasn't done well. Both failed on the bench at 12 volts, I heard a rev drop and the endbell looked like a ground display at the fireworks show.
Im over it. If the 6 ohms burns it burns, I have lots of replacements on that motor.
|
|
|
|
Post by pete on Aug 18, 2021 16:22:53 GMT -7
I can't find tyco timmed 2.4ohm ,only for viper. So I haven't blown any up lol. "I had a friend went to the race track armed with a Hot Tip and a Hundred dollar bill, that boy had to walk back home." Good luck Sam  |
|
|
|
Post by dave632 on Aug 18, 2021 16:26:20 GMT -7
I have not tried any of my 2.5s at 26v but I am pretty sure the BSRT G3 armature will hold up, they have a pretty decent comm. I will let all know when I do
some testing. When I did a hot wind on a low cost armature the comm plates came right off first pass.
|
|
|
|
Post by AJR on Aug 18, 2021 16:39:16 GMT -7
In the past BSRT, MRT, and Viper arms all held up. The SG+ type chassis was dominant.
|
|
|
|
Post by pete on Aug 18, 2021 17:12:50 GMT -7
Well these were SG+ arms. I think I got the friday after lunch ones.
I'm getting a wiff of old school BS. I didn't say who they belonged to..
Ive said it before and say it again. These old school slot wars are as dead as the ones that relive it will be one day. Not sure why one needs to cross over for things to get better day by day in the slot world , but so be it. I can wait.
Dave I think the BSRT will hold up to.
|
|
|
|
Post by skillet on Aug 18, 2021 20:14:48 GMT -7
Thanks WJB. I have Slottech 2.7 arms just can't find lower unless it's way lower. I'm stubborn I want to stay with tyco timmed.
Not much difference in ohms but still if I had a tyco 2.4 you better believe I'd run it :-)
|
|
|
|
Post by pete on Aug 19, 2021 2:20:39 GMT -7
Im just a bit frustrated with not having it work out for me. I payed a lot for those 2.00 motors. Frustrated I forgot to stay within my race box.
|
|
|
|
Post by crazynski on Aug 19, 2021 6:11:25 GMT -7
Pete,
Thank you very kindly for the information. As Yoda might say. "Paying attention, I am".
I'm content to be a newbie in the slower classes. I haven't quite figured those out yet either. But I'm still having fun.
|
|
